# Kammprofildichtung, Silberauflage, Profil KD01-KD10-KD20-KD30, WS 1.4828/Silber, Dichtungsdicke 4,8 mm, Rev. 03

Type of gasket:Kammprofile gasketGasket manufacturer:IDT Industrie- und Dichtungstechnik GmbHGasket label:Grooved gasket, silver layer, Profile KD01-KD10-KD20-KD30, WS 1.4828/silber, thickness 4,8 mm, Rev. 03maximum temperature:600 °Cmaximum pressure:80 bar

## Inhaltsverzeichnis

- [Gasket thickness under load eG](#kennwerte-en-15333-dichtungshoehe-unter-last)
- [Gasket deformation under load ΔeG](#kennwerte-en-15333-dichtungsverformung-unter-last)
- [Maximum allowable gasket stress QSmax](#kennwerte-en-15333-maximale-flaechenpressung)
- [Modulus of elasticity EG](#kennwerte-en-15333-ersatzelastizitaetsmodul)
- [Creep/relaxation factor PQR](#kennwerte-en-15333-kennzahlen-kriechfaktor)
- [Minimum required gasket stress in assembly Qmin(L)](#kennwerte-en-15333-mindestflaechenpressung-einbau)
- [Minimum required gasket stress in service QSmin(L)](#kennwerte-en-15333-mindestflaechenpressung-betrieb)
- [Friction coefficient µG](#kennwerte-en-15333-reibungskoeffizient)

## Downloads

**- [PDF](https://gasketdata.amtec.de/DataSheets/IDT/IDT-KD01-10-20-30-WS%201.4828-Silber-4,8%20mm-IDT-RevXX.pdf)
- [Temesfl.cal](https://gasketdata.amtec.de/export/temesfl/28C8/294)**

## Gasket thickness under load eG

No data available.

## Gasket deformation under load ΔeG

No data available.

## Maximum allowable gasket stress QSmax

Temperature / °CQSmax / MPa20 600200 600400 600600 200

## Modulus of elasticity EG

Modulus of elasticity EG / MPaGasket stress / MPa20°C200°C400°C600°C20196000182000166000150000200150000600196000182000166000

## Creep/relaxation factor PQR

Creep/relaxation factor PQRGasket stress / MPa20°C200°C400°C600°C400.980.570.330.48800.980.630.410.512000.726000.990.90.86

## Minimum required gasket stress in assembly Qmin(L)

Minimum required gasket stress Qmin(L) / MPaLeakage rate / mg/m/s10 bar40 bar80 bar 10⁰ 202087 10⁻¹ 6475102 10⁻² 8390106 10⁻³ 98103111 10⁻⁴ 104115116 10⁻⁵ 109123121 10⁻⁶ 114129128 10⁻⁷ 119135135 10⁻⁸ 272169244

## Minimum required gasket stress in service QSmin(L) depending on initial gasket stress QA

- [Internal pressure 10 bar](#mindestflaechenpressung-innendruck-10)
- [Internal pressure 40 bar](#mindestflaechenpressung-innendruck-40)
- [Internal pressure 80 bar](#mindestflaechenpressung-innendruck-80)

## Minimum required gasket stress at internal pressure 10 bar

## Minimum required gasket stress at internal pressure 40 bar

## Minimum required gasket stress at internal pressure 80 bar

## Friction coefficient µG

The friction coefficient between gasket and flange surface was determined for different types of gasket materials in an ESA research project.

 The gasket Grooved gasket, silver layer, Profile KD01-KD10-KD20-KD30, WS 1.4828/silber, thickness 4,8 mm, Rev. 03 can be assigned to the categorie 0 : "Custom". Therefore, the following friction coefficients can be considered:

Temperature / °CFriction coefficient0 °C 0

## Historie EN 15333

[Excel](https://gasketdata.amtec.de/export/temesfl/28C8/294)[Temesfl.cal](https://gasketdata.amtec.de/export/temesfl/28C8/294)