# Spiraldichtung mit Innen- und Außenring, Glimmerfüllung, Profil SD10, WS 1.4828/Glimmer/1.4828, Dichtungsdicke 5.2 mm, Rev. 00

Type of gasket:Spiralwound gasketGasket manufacturer:IDT Industrie- und Dichtungstechnik GmbHGasket label:Spiraldichtung mit Innen- und Außenring, Glimmerfüllung, Profil WS 1.4828/Glimmer/1.4828, Dichtungsdicke 5.2 mm, Rev. 00maximum temperature:600 °Cmaximum pressure:16 bar

## Inhaltsverzeichnis

- [Gasket thickness under load eG](#kennwerte-en-15333-dichtungshoehe-unter-last)
- [Gasket deformation under load ΔeG](#kennwerte-en-15333-dichtungsverformung-unter-last)
- [Maximum allowable gasket stress QSmax](#kennwerte-en-15333-maximale-flaechenpressung)
- [Modulus of elasticity EG](#kennwerte-en-15333-ersatzelastizitaetsmodul)
- [Creep/relaxation factor PQR](#kennwerte-en-15333-kennzahlen-kriechfaktor)
- [Minimum required gasket stress in assembly Qmin(L)](#kennwerte-en-15333-mindestflaechenpressung-einbau)
- [Minimum required gasket stress in service QSmin(L)](#kennwerte-en-15333-mindestflaechenpressung-betrieb)
- [Friction coefficient µG](#kennwerte-en-15333-reibungskoeffizient)

## Downloads

**- [PDF](https://gasketdata.amtec.de/DataSheets/IDT/IDT-SD10-WS%201.4828-Glimmer-5,2%20mm-IDT-Rev00.pdf)
- [Temesfl.cal](https://gasketdata.amtec.de/export/temesfl/28C8/352)**

## Gasket thickness under load eG

Gasket thickness eG / mmGasket stress / MPa20°C300°C600°C05.35.255.25515.195.2155.225204.6884.4734.407304.5444.2274.38404.4034.0894.333504.2893.9924.283604.1863.9134.228804.0563.7594.064

## Gasket deformation under load ΔeG

Gasket deformation ΔeG / mmGasket stress / MPa20°C300°C600°C00.0000.0000.00010.1100.0350.030200.6120.7770.848300.7561.0230.875400.8971.1610.922501.0111.2580.972601.1141.3371.027801.2441.4911.191

## Maximum allowable gasket stress QSmax

Temperature / °CQSmax / MPa20 80300 80600 80

## Modulus of elasticity EG

Modulus of elasticity EG / MPaGasket stress / MPa20°C300°C600°C201805182880703022142238588440266431296324503063350866816034063775679780434547047281

## Creep/relaxation factor PQR

Creep/relaxation factor PQRGasket stress / MPa20°C300°C600°C200.810.550.31400.860.440.26800.890.360.29

## Minimum required gasket stress in assembly Qmin(L)

Minimum required gasket stress Qmin(L) / MPaLeakage rate / mg/m/s10 bar16 bar 10⁰ 66 10⁻¹ 2531 10⁻² 4458 10⁻³ 78

## Minimum required gasket stress in service QSmin(L) depending on initial gasket stress QA

- [Internal pressure 10 bar](#mindestflaechenpressung-innendruck-10)
- [Internal pressure 16 bar](#mindestflaechenpressung-innendruck-16)

## Minimum required gasket stress at internal pressure 10 bar

## Minimum required gasket stress at internal pressure 16 bar

## Friction coefficient µG

The friction coefficient between gasket and flange surface was determined for different types of gasket materials in an ESA research project.

 The gasket Spiraldichtung mit Innen- und Außenring, Glimmerfüllung, Profil WS 1.4828/Glimmer/1.4828, Dichtungsdicke 5.2 mm, Rev. 00 can be assigned to the categorie 0 : "Custom". Therefore, the following friction coefficients can be considered:

Temperature / °CFriction coefficient0 °C 0

## Historie EN 15333

[Excel](https://gasketdata.amtec.de/export/temesfl/28C8/352)[Temesfl.cal](https://gasketdata.amtec.de/export/temesfl/28C8/352)