Flachdichtung SIGRAFLEX® Hochdruck Pro mit Innenbördel (1.4571, s=0,1), Profil FD10, WS 3888 IB, Dichtungsdicke 2 mm, Rev. 01
SIGRAFLEX® HOCHDRUCK PRO, impregnated, with adhesive-free insert made from 0.05 mm stainless steel foil 316L and eyelet made from stainless steel 1.4571
Article Number
3888FD10
Material
3888
Profile
FD10
| Type of gasket: | Sheet gasket with inner eyelet |
|---|---|
| Gasket manufacturer: | IDT Industrie- und Dichtungstechnik GmbH |
| Gasket label: | SIGRAFLEX® Hochdruck Pro with inner eyelet (1.4571, s=0,1), FD10, WS 3888 IB, thickness 2 mm, Rev. 01 |
| maximum temperature: | 400 °C |
| maximum pressure: | 160 bar |
Inhaltsverzeichnis
Downloads
Gasket thickness under load eG
| Gasket thickness eG / mm | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Gasket stress / MPa | 20°C | 150°C | 300°C | 400°C | |||||||||
| 1 | 1.998 | 1.973 | 1.903 | 1.924 | |||||||||
| 20 | 1.508 | 1.475 | 1.467 | 1.482 | |||||||||
| 30 | 1.419 | 1.399 | 1.414 | 1.426 | |||||||||
| 40 | 1.372 | 1.352 | 1.361 | 1.369 | |||||||||
| 50 | 1.327 | 1.306 | 1.322 | 1.318 | |||||||||
| 60 | 1.294 | 1.272 | 1.289 | 1.289 | |||||||||
| 80 | 1.252 | 1.219 | 1.242 | 1.227 | |||||||||
| 100 | 1.215 | 1.189 | 1.21 | 1.191 | |||||||||
| 120 | 1.188 | 1.172 | 1.185 | 1.14 | |||||||||
| 140 | 1.168 | 1.158 | |||||||||||
| 160 | 1.156 | 1.146 | |||||||||||
| 180 | 1.147 | ||||||||||||
| 200 | 1.135 | ||||||||||||
Gasket deformation under load ΔeG
| Gasket deformation ΔeG / mm | |||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Gasket stress / MPa | 20°C | 150°C | 300°C | 400°C | |||||||||
| 1 | 0.000 | 0.000 | 0.000 | 0.000 | |||||||||
| 20 | 0.490 | 0.498 | 0.436 | 0.442 | |||||||||
| 30 | 0.579 | 0.574 | 0.489 | 0.498 | |||||||||
| 40 | 0.626 | 0.621 | 0.542 | 0.555 | |||||||||
| 50 | 0.671 | 0.667 | 0.581 | 0.606 | |||||||||
| 60 | 0.704 | 0.701 | 0.614 | 0.635 | |||||||||
| 80 | 0.746 | 0.754 | 0.661 | 0.697 | |||||||||
| 100 | 0.783 | 0.784 | 0.693 | 0.733 | |||||||||
| 120 | 0.810 | 0.801 | 0.718 | 0.784 | |||||||||
| 140 | 0.830 | 0.815 | |||||||||||
| 160 | 0.842 | 0.827 | |||||||||||
| 180 | 0.851 | ||||||||||||
| 200 | 0.863 | ||||||||||||
Maximum allowable gasket stress QSmax
| Temperature / °C | QSmax / MPa |
|---|---|
| 20 | 200 |
| 150 | 160 |
| 300 | 120 |
| 400 | 120 |
Modulus of elasticity EG
| Modulus of elasticity EG / MPa | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Gasket stress / MPa | 20°C | 150°C | 300°C | 400°C | ||||||||
| 20 | 314 | 474 | 418 | 394 | ||||||||
| 30 | 505 | 584 | 864 | 621 | ||||||||
| 40 | 933 | 910 | 1131 | 926 | ||||||||
| 50 | 976 | 1087 | 1418 | 869 | ||||||||
| 60 | 1329 | 1398 | 1610 | 1579 | ||||||||
| 80 | 2176 | 1804 | 2417 | 1685 | ||||||||
| 100 | 2404 | 2637 | 3226 | 2241 | ||||||||
| 120 | 2858 | 3914 | 3653 | 3103 | ||||||||
| 140 | 3310 | 4527 | ||||||||||
| 160 | 4759 | 5165 | ||||||||||
| 180 | 6620 | |||||||||||
| 200 | 7071 | |||||||||||
Creep/relaxation factor PQR
| Creep/relaxation factor PQR | |||||
|---|---|---|---|---|---|
| Gasket stress / MPa | 20°C | 150°C | 300°C | 400°C | |
| 30 | 0.99 | 0.93 | 0.92 | 0.92 | |
| 50 | 0.99 | 0.96 | 0.95 | 0.95 | |
| 120 | 0.97 | 0.97 | |||
| 160 | 0.99 | ||||
| 200 | 1 | ||||
Minimum required gasket stress in assembly Qmin(L)
| Minimum required gasket stress Qmin(L) / MPa | ||||||
|---|---|---|---|---|---|---|
| Leakage rate / mg/m/s | 10 bar | 40 bar | 80 bar | 100 bar | 160 bar | |
| 10⁰ | 5 | 5 | 20 | 20 | 20 | |
| 10⁻¹ | 5 | 9 | 20 | 20 | 29 | |
| 10⁻² | 7 | 20 | 33 | 41 | 63 | |
| 10⁻³ | 24 | 49 | 67 | 77 | 88 | |
| 10⁻⁴ | 55 | 104 | 107 | 127 | ||
| 10⁻⁵ | 133 | 136 | 176 | |||
Minimum required gasket stress in service QSmin(L) depending on initial gasket stress QA
- Internal pressure 10 bar
- Internal pressure 40 bar
- Internal pressure 80 bar
- Internal pressure 100 bar
- Internal pressure 160 bar
Minimum required gasket stress at internal pressure 10 bar
Minimum required gasket stress at internal pressure 40 bar
Minimum required gasket stress at internal pressure 80 bar
Minimum required gasket stress at internal pressure 100 bar
Minimum required gasket stress at internal pressure 160 bar
Friction coefficient µG
The friction coefficient between gasket and flange surface was determined for different types of gasket materials in an ESA research project.
The gasket SIGRAFLEX® Hochdruck Pro with inner eyelet (1.4571, s=0,1), FD10, WS 3888 IB, thickness 2 mm, Rev. 01 can be assigned to the categorie 3 : "Gaskets based on flexible graphite". Therefore, the following friction coefficients can be considered:
| Temperature / °C | Friction coefficient |
|---|---|
| 20 °C | 0.22 |