Flachdichtung UNIFLUOR® PTFE mit Füllstoff Bariumsulfat, Profil FD01, WS 7553, Dichtungsdicke 2 mm, Rev. 01

UNIFLUOR® WS 7553 is a high quality biaxially orientated sealing material on PTFE basis, filled with barium sulphate.

Article Number

7553FD01

Material

7553

Profile

FD01

Type of gasket:	Type IBC - flat gasket
Gasket manufacturer:	IDT Industrie- und Dichtungstechnik GmbH
Gasket label:	Flachdichtung UNIFLUOR® PTFE mit Füllstoff Bariumsulfat, Profil FD01, WS 7553, Dichtungsdicke 2 mm, Rev. 01
maximum temperature:	200 °C
maximum pressure:	40 bar

Inhaltsverzeichnis

Gasket thickness under load e_G
Gasket deformation under load Δe_G
Maximum allowable gasket stress Q_Smax
Modulus of elasticity E_G
Creep/relaxation factor P_QR
Minimum required gasket stress in assembly Q_min(L)
Minimum required gasket stress in service Q_Smin(L)
Friction coefficient µ_G

Downloads

PDF

Temes_fl.cal

Gasket thickness under load e_G

	Gasket thickness e_G / mm
Gasket stress / MPa	20°C	100°C	150°C	200°C
0	1.985	2.03	2.04	2.025
1	2.034	2.013	2	2.018
5	2.016	2.002	1.992	2.007
10	2.005	1.982	1.923	1.858
15	1.994	1.914	1.735	1.602
20	1.974	1.776	1.563	1.412
30	1.92	1.499	1.3	1.182
40	1.823	1.305	1.145	1.048
50	1.7	1.174
60	1.592
80	1.431

Gasket deformation under load Δe_G

	Gasket deformation Δe_G / mm
Gasket stress / MPa	20°C	100°C	150°C	200°C
0	0.000	0.000	0.000	0.000
1	-0.049	0.017	0.040	0.007
5	-0.031	0.028	0.048	0.018
10	-0.020	0.048	0.117	0.167
15	-0.009	0.116	0.305	0.423
20	0.011	0.254	0.477	0.613
30	0.065	0.531	0.740	0.843
40	0.162	0.725	0.895	0.977
50	0.285	0.856
60	0.393
80	0.554

Maximum allowable gasket stress Q_Smax

Temperature / °C	Q_Smax / MPa
20	70
100	50
150	40
200	40

Modulus of elasticity E_G

	Modulus of elasticity E_G / MPa
Gasket stress / MPa	20°C	100°C	150°C	200°C
5	1363	2553	998	673
10	2938	4877	1281	742
15	2716	2679	1398	934
20	1992	2554	1498	1144
30	2473	2527	1530	1280
40	2384	2989	1592	1389
50	2469	2984
60	2734
80	3073

Creep/relaxation factor P_QR

	Creep/relaxation factor P_QR
Gasket stress / MPa	20°C	100°C	150°C	200°C
10			0.76	0.63
20	0.96	0.63	0.5	0.41
30		0.51	0.41	0.33
40	0.85	0.47	0.36	0.32
50		0.46
60	0.82
70	0.8

Minimum required gasket stress in assembly Q_min(L)

	Minimum required gasket stress Q_min(L) / MPa
Leakage rate / mg/m/s	10 bar	16 bar	40 bar
10⁰	5	8	15
10⁻¹	14	17	22
10⁻²	21	23	28
10⁻³	26	28	33
10⁻⁴	30	35	39
10⁻⁵	44	57

Minimum required gasket stress in service Q_Smin(L) depending on initial gasket stress QA

Internal pressure 10 bar
Internal pressure 16 bar
Internal pressure 40 bar

Minimum required gasket stress at internal pressure 10 bar

Minimum required gasket stress at internal pressure 16 bar

Minimum required gasket stress at internal pressure 40 bar

Friction coefficient µ_G

The friction coefficient between gasket and flange surface was determined for different types of gasket materials in an ESA research project.

The gasket Flachdichtung UNIFLUOR® PTFE mit Füllstoff Bariumsulfat, Profil FD01, WS 7553, Dichtungsdicke 2 mm, Rev. 01 can be assigned to the categorie 2 : "Gaskets based on filled PTFE". Therefore, the following friction coefficients can be considered:

Temperature / °C	Friction coefficient
20 °C	0.23

Historie EN 15333

Excel Temes_fl.cal

Filter

Inhaltsverzeichnis

Downloads

Gasket thickness under load eG

Gasket deformation under load ΔeG

Maximum allowable gasket stress QSmax

Modulus of elasticity EG

Creep/relaxation factor PQR

Minimum required gasket stress in assembly Qmin(L)

Minimum required gasket stress in service QSmin(L) depending on initial gasket stress QA